J-35597-A Cylinder Liner Installer Tool for 60 Series Detroit Diesel 5874. Detroit Diesel 60 series. J-35597-A precisely installs the cylinder liner on the Detroit 60 Series Diesel. Detroit Diesel 60 Series J-35597-A 5874 Cylinder Liner Installer OEM DD60 Tool Alternative. This alternative to J-35597-A and 5874 was manufactured to install cylinder liners on Detroit Diesel 60 Series engines. After inserting liner into the block, simply attach the installer tool using three cylinder head bolts. As the drive screw is tightened the installer plate presses the cylinder liner firmly into the engine block until it’s properly seated. Install the cylinder liner as follows. Wipe the inside and outside of the liner clean. Be sure the block bore and counter bore are clean, so the liner flange will seat properly. The block counter bore depth must be 8.9246-8.9746 mm 0.3514-0.3533 in. And must not vary more than 0.04 mm 0.0015 in. In depth around the circumference. No two adjacent block counter bores may range in depth more than 0.025 mm 0.001 in. When gaged along the longitudinal cylinder block centerline. Note: Thoroughly clean the cylinder block liner counter bores to remove any foreign material. Foreign material in the cylinder liner counter bores can cause the liner to seat improperly. Note: If the firedeck surface of the cylinder block has been machined, the counter bores must be machined the same amount to keep the cylinder liner counter bore depth within limits. Lubricate the seal rings and crevice seal with clean petroleum jelly. Install two new seal rings and a new crevice seal into their respective grooves in the liner. Insert the cylinder liner into the cylinder bore. Note: Do not exert excessive force on the liner, while pushing it down. Install the cylinder liner installation tool, J-35597-A, over the liner to be installed. Note: It is necessary to leave the cylinder liner installation tool in place until after the liner protrusion is measured. Thread three cylinder head bolts through the tool and into a head bolt hole, so that the round shoe of the tool is centered over the liner. Note: It is not necessary to torque the bolts. Turn the threaded center bolt in a clockwise direction. As the round shoe of the tool reaches the liner, ensure that the shoe is properly positioned into the cylinder liner. Continue turning the bolt until the liner bottoms in the cylinder counterbore. Apply a tightening torque of 60 N · m (44 lb · ft) to the installation tool center bolt. Install a dial indicator sled gage. Measure the distance from the top of the liner flange to the top of the block. Allowable liner protrusion is -0.0127-0.0762 mm -0.0005-0.003 in. With no more than 0.05 mm 0.002 in. Variation between any two adjacent cylinders. If the liner protrusion exceeds the maximum allowable, remove the liner and check for debris under the liner flange. Remove the cylinder liner tool. With all of the cylinder liners installed and the liner protrusion measurements within specifications, install the piston and connecting rod asse. The item “Cylinder Liner Installer J-35597-A For Detroit Diesel 60 Series Engines 14&12.7L” is in sale since Thursday, July 22, 2021. This item is in the category “eBay Motors\Automotive Tools & Supplies\Hand Tools\Other Automotive Hand Tools”. The seller is “dearchan1965″ and is located in Stockton, California. This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, China, Sweden, South Korea, Indonesia, Taiwan, South africa, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Bahamas, Israel, Mexico, New Zealand, Philippines, Singapore, Switzerland, Norway, Saudi arabia, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Brazil, Chile, Colombia, Costa rica, Dominican republic, Panama, Trinidad and tobago, Guatemala, El salvador, Honduras, Jamaica, Antigua and barbuda, Aruba, Belize, Dominica, Grenada, Saint kitts and nevis, Saint lucia, Montserrat, Turks and caicos islands, Barbados, Bangladesh, Bermuda, Brunei darussalam, Bolivia, Ecuador, Egypt, French guiana, Guernsey, Gibraltar, Guadeloupe, Iceland, Jersey, Jordan, Cambodia, Cayman islands, Liechtenstein, Sri lanka, Luxembourg, Monaco, Macao, Martinique, Maldives, Nicaragua, Oman, Peru, Pakistan, Paraguay, Reunion, Viet nam, Uruguay, Russian federation.

• Type: Cylinder Liner Installer
• Manufacturer Part Number: J-35597-A
• Brand: Unbranded