APPLICATION — Fits for Detroit Diesel Series 60, two cycle 92 engines. Used to install multiple Seal & Wear Sleeve Assemblies including 23516969 23513578 23513485 23518355 23519651. OEM REFERENCES — Replace Part Number: J-35686-B, J-35686, J-35686-A. ADVANTAGE — Heavy duty J-35686-B Seal & Wear Sleeve Installer for Detroit. This tool is easier to use due to a simpler design. Protect your engine by preventing wear sleeve lip flare by using our low-priced but Quality installation tools. BENEFITS — This tool set installs the front and rear crankshaft wear sleeves and seals. It eliminates lip flare on the wear sleeve and installs the seal properly. Manufactured from quality steel, using top of the line machining and measuring equipment to ensure each part is manufactured to OEM specifications. Lubricate the rubber outer diameter of the oil seal with clean engine oil. Lubricate the gear case cover or flywheel housing bore with clean engine oil. Failure to lubricate the outside of the seal and the inside of the bore prior to installation may damage seal causing seal to leak. Install two guide studs (J-35686-2, part of tool set J-35686-B) through the holes provided in the center guide assembly (J-35686-1, part of tool set J-35686-B) and into two of the tapped holes in the crankshaft 180 degrees apart. Tighten the guide studs using the appropriate wrench on the flats of the studs. The base must be tight against the end of the crankshaft. Install the spacers to the center screw of the base. Slide the oil seal assembly over the installer base as far onto the crankshaft hub as possible. Slide collar with the stepped side contacting the seal. Slide the installer cup over the guide studs and installer base. Lubricate the center screw of the base with extreme pressure lubricant (J-23444-A, part of tool set J-41329). Install the thrust bearing with the case side toward the installer cup and install the hex nut to the center screw of the base. Finger tighten the hex nut until snug. Install a ratchet and socket onto the hex nut. Tighten the hex nut until the oil seal and wear sleeve are pressed into the flywheel housing or gear case cover. When the inside surface of the housing is seated firmly against the base and spacers the seal and sleeve are properly installed. Measure the face squareness of the outside diameter of the crankshaft seal using a runout gage installed on the crankshaft. If the total indicator reading is more then 0.762 mm 0.030 in. The seal must be removed and a new seal installed. This item is in the category “eBay Motors\Automotive Tools & Supplies\Hand Tools\Other Automotive Hand Tools”. The seller is “dearchan1965″ and is located in this country: US. This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech Republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, Sweden, Korea, South, Indonesia, Taiwan, South Africa, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Bahamas, Israel, Mexico, New Zealand, Philippines, Singapore, Switzerland, Norway, Saudi Arabia, United Arab Emirates, Qatar, Kuwait, Bahrain, Croatia, Republic of, Malaysia, Brazil, Chile, Colombia, Costa Rica, Dominican Republic, Panama, Trinidad and Tobago, Guatemala, El Salvador, Honduras, Jamaica, Antigua and Barbuda, Aruba, Belize, Dominica, Grenada, Saint Kitts-Nevis, Saint Lucia, Montserrat, Turks and Caicos Islands, Barbados, Bangladesh, Bermuda, Brunei Darussalam, Bolivia, Ecuador, Egypt, French Guiana, Guernsey, Gibraltar, Guadeloupe, Iceland, Jersey, Jordan, Cambodia, Cayman Islands, Liechtenstein, Sri Lanka, Luxembourg, Monaco, Macau, Martinique, Maldives, Nicaragua, Oman, Peru, Pakistan, Paraguay, Reunion, Vietnam, Uruguay.
- Replace Part Number: J-35686-B , J-35686 , J-35686-A
- to Install Seal p/n: 23516969 , 23513578, 23513485 , 23518335, 23519651
- Type: Seal Wear Sleeve Installer
- Manufacturer Part Number: J-35686-B
- Brand: Camoo
- Warranty: 1 Year